page . 1 stad-jan.29.2007 sbu6a~sbu6m features ? plastic material has underwriters laboratory flammability classification 94v-o ideal for printed circuit board reliable low cost construction ulilizing molded pastic technique. high temperature soldering guaranteed: 260c/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension in compliance with eu rohs 2002/95/ec directives mechanical data silicon single-phase bridge rectifier case: reliable low cost construction utilizing molded plastic technique terminals: leads solderable per mil-std-750, method 2026 mounting position: any mounting torque: 5 in. lb. max. weight: 0.2 ounce, 5.6 grams maximum ratings and electrical characteristics rating at 25cambient temperature unless otherwise specified. resistive or inductive load, 60hz. for capacitive load derate current by 20%. notes: 1. recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 s crew. 2. units mounted in free air, no heatsink, p.c.b at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads. 3. units mounted on a 2.0 x 1.6" x 0.3" thick (5 x 4 x 0.8cm) al plate. voltage 50 to 1000 volts 6.0 amperes current r e t e m a r a pl o b m y s a 6 u b sb 6 u b sd 6 u b sg 6 u b sj 6 u b sk 6 u b sm 6 u b s s t i n u e g a t l o v e s r e v e r k a e p t n e r r u c e r m u m i x a m v m r r 0 50 0 10 0 20 0 40 0 60 0 80 0 0 1 v e g a t l o v t u p n i e g d i r b s m r m u m i x a m v s m r 5 30 70 4 10 8 20 2 40 6 50 0 7 v e g a t l o v g n i k c o l b c d m u m i x a m v c d 0 50 0 10 0 20 0 40 0 60 0 80 0 0 1 v t d r a w r o f e g a r e v a m u m i x a m c 0 0 1 = o c t t a t n e r r u c t u p t u o d e i f i t c e r a 0 4 = o c i ( f) v a 0 . 6 a i 2 ) s m 3 . 8 < t ( g n i s u f r o f g n i t a r t i 2 t 0 1 2 a 2 c e s d e t a r n o d e s o p m i r e p u s e v a w - e n i s e l g n i s t n e r r u c e g r u s d r a w r o f k a e p ) d o h t e m c e d e j ( d a o l i m s f 5 2 2 k p a a 0 . 6 t a t n e m e l e e g d i r b r e p p o r d e g a t l o v d r a w r o f m u m i x a m v f 8 9 . 0 k p v t @ d e t a r t a t n e r r u c e g a k a e l e s r e v e r m u m i x a m a 5 2 = o c t @ e g a t l o v g n i k c o l b c d a 0 0 1 = o c i r 0 . 3 0 0 0 1 a u ) 2 e t o n ( g e l r e p e c n a t s i s e r l a m r e h t l a c i p y t ) 3 e t o n ( g e l r e p e c n a t s i s e r l a m r e h t l a c i p y t r a j r c j 0 . 7 1 0 . 3 o w / c e g n a r e r u t a r e p m e t e g a r o t s d n a n o i t c n u j g n i t a r e p o t j ,t g t s 0 5 1 + o t 5 5 - o c
page . 2 stad-jan.29.2007 sbu6a~sbu6m rating and characteristic curves temperature, c o percent of peak revere voltage,% instantaneous reverse current,ua 8 6 . . 0 0 4.0 2.0 0 0 50 100 150 fig.1 - derating curve for output rectified current average forward current amperes instantaneous forward voltage, volts instantaneous forward current, amperes fig.4 - typical instantaneous forward characteristics per element 10 1.0 0.1 0.01 02040 6080100120140 fig.3 - typical reverse characteristics t=25 c j o t =100 c j o no. of cycles at 60hz fig.2 - maximum non-repetitive peak forward surge current forwrd surge current, amperes pk (half sine-wave) capacitance, pf fig.5 - typical junction capacitance reverse voltage, volts 0.5"(12.7mm) lead length 60hz resistive or inductive load heat-sink mounting, tc (4x4x0.15)inch copper plate 12 6 10 20 40 60 100 225 180 135 90 45 0 100 40 20 10 4.0 2.0 1.0 0.4 0.2 0.1 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 tj=25 c pulse width = 300us 1% duly cycle o 400 100 50 10 1 5 10 50 100 t=25c f=1mhz visg=50mvp-p j o
|
